[Notification of CAD Data Download Issue]
We regret to inform you that we are currently experiencing issues with downloading CAD data for some products.
We are investigating the cause of this problem. We apologize for any inconvenience this may cause and appreciate your understanding.
Business > Industrial Devices > Automation Controls Top > Components & Devices > Relays / Couplers > Interface Terminal > RT-3 UNIT RELAY (PhotoMOS Power type) /4-POINT TERMINAL (Without relay type) > Rating/Performance
Part No. | Rated input voltage | Operate voltage (at 25°C) |
Release voltage (at 25°C) |
Input current during application of rated input voltage (at 25°C) |
Allowable variation of rated input voltage (at -20 to +55°C) |
---|---|---|---|---|---|
AY34001 | 12 V DC | Max. 9.5 V DC (5.1 V typ.) |
Min. 3.0 V DC (5.0 V typ.) |
6.2 mA typ. | 90 to 110% V of rated input voltage |
AY35001 | |||||
AY34002 | 24 V DC | Max. 15.0 V DC (6.8 V typ.) |
Min. 3.5 V DC (6.5 V typ.) |
6.7 mA typ. | |
AY35002 |
* | This product has a built-in input current limiting resistor; therefore, it is not necessary to externally connect a resistor to the input. The input voltage can be applied directly. |
---|
Part No. | Equipped relay | Max. load voltage | Recommended voltage | Continuous load current | Peak load currant |
---|---|---|---|---|---|
AY34001 | AQZ102 (DC only) |
60 V (DC) | 0 to 30 V (DC) | 2 A (DC) | 9 A (100 ms 1 shot) |
AY34002 | |||||
AY35001 | AQZ204 (AC/DC dual use) |
400 V (DC, AC peak value) |
0 to 200 V (DC) 0 to 125 V (AC) |
0.3 A (DC, AC peak value) |
1.5 A (100 ms 1 shot) |
AY35002 |
*1 | During 4-point simultaneous operation, the rating per point is also as shown in the table above. |
---|---|
*2 | The load current varies depending on ambient temperature. Refer to the “REFERENCE DATA Load current vs. ambient temperature characteristics”. |
Item | Specifications | Condition | |
---|---|---|---|
Dielectric strength (initial) |
Between input and output |
2,000 V AC | for 1 min |
Between different terminals (between relays, both ways) |
1,500 V AC | for 1 min | |
Insulation resistance | Min. 100 MΩ (Measured portion is the same as the case of dielectric strength.) |
Using 500 V DC megger | |
Shock resistance | Destructive shock resistance |
Min. 196 m/s2 | In vertical, horizontal and longitudinal directions |
Destructive vibration resistance |
10 to 55 Hz at double amplitude of 1 mm | In vertical, horizontal and longitudinal directions | |
Use condition | Ambient temperature | -20 to +55°C | Avoid icing and condensation |
Ambient humidity | 35 to 85% RH | Avoid condensation | |
Storage temperature | -30 to +80°C | Avoid icing and condensation | |
Terminal screw fasten torque | 0.3 to 0.5 N·m (3 to 5 kgf·cm) | ||
Cross connection protecting diode | 1 A, inverse voltage 400 V | ||
Unit weight | Approx. 100 g |
*1 | Dielectric strength and insulation resistance are initial values. |
---|---|
*2 | Condensing occurs when the unit relay is exposed to sudden temperature change in a high temperature and high humidity atmosphere. This may cause some troubles like insulation failure of the socket or the PC board. Take care under this condition. |
*3 | Below 0°C, condensing water can freeze and cause socket contact failures and other problems. Take care under this condition. |
Allowable ambient temperature: –20°C to +55°C
|
Allowable ambient temperature: –20°C to +55°C
|
Requests to customers (Automation Control Components & Industrial Device) [Excluding specific product]
Requests to customers (Automation Control Components & Industrial Device) [For specific product]
Requests to customers (FA Sensors & Components [Excluding motors])
Requests to customers (Dedicated to industrial motors)