FP Loader Ver2.60

请在使用版本升级之前仔细阅读以下信息。

限制事项

FP Loader (hereinafter referred to as this software) utility is designed to download, to a PLC, program files created with NPST-GR or FPWIN. It supports all FP series PLCs(without FP7, FP-XH Ethernet type and FP0H).

  • Programs cannot be uploaded.
  • Only program files can be downloaded. (Comments, etc., cannot be downloaded.)
  • The USB port of FP0R can be used in case the USB driver is "PIDSX PLC USB-COM".
    The other driver like "Panasonic Electric Works PLC Virtual UART" is not available.

You cannot download programs under the following conditions.

  • When reading of a file fails.
  • When communication with the PLC cannot be established
  • When the PLC is in RUN mode.
    (You can switch to REMOTE-PROG when the PLC is in REMOTE-RUN mode.)
  • When the PLC type of the selected file is different from the PLC type actually connected
    (including difference in capacity).
  • When the PLC is password protected and the password is unknown.

Version-Up Information (Ver.2.50 to Ver.2.60)

  • Changed the company name to Panasonic Industry Co., Ltd. due to the business succession. (License agreement etc.)
  • Supported FP-XH except Ethernet type.

Version-Up Information (Ver.2.40 to Ver.2.50)

  • Supports FP2SH 32K.
  • Supports FP-X0.

Version-Up Information (Ver.2.30 to Ver.2.40)

  • Supports FP0R.
    note) The USB port of FP0R can not be used.

Version-Up Information (Ver.2.21 to Ver.2.30)

  • Supports FP-X transistor type.

Version-Up Information (Ver.2.20 to Ver.2.21)

  • The problem, that the data value became 0, was improved, even if you did not check [Clear Data].

Version-Up Information (Ver.2.10 to Ver.2.20)

  • Supports FPSigma 32K.

Version-Up Information (Ver.1.22 to Ver.2.10)

The following points have been upgraded.

  • Supports FP-X.
  • Prepare 3 modes as download method.
  • - 1:1 : : Downloads the specified file for the PLC directly connected.
    - 1:1(Unit number changing is possible) : Downloads the system register changing the PLC unit number for the PLC directly connected.
    - 1:N : Downloads the specified file to the multiple PLC units.
  • Improve the download function, when you check [Clear data].
  • PLC data can be cleared before downloading.
  • PLC mode can be changed when continuously processing downloading.
  • Improve the automatic COM port scan.

系统要求

请确认安装本软件的计算机是否满足以下的最低配置要求。

OS Windows 10*1/ 11
Language The display language will be Japanese when a Japanese OS is used. Otherwise the display language will be English.
Applicable PLCs All FP series (without FP7, FP-XH Ethernet type and FP0H)
※1 64 bit edition

软件使用许可协议

使用本软件的条件是您同意本软件使用许可协议的内容。请仔细查阅内容,必须在您同意的情况下才能下载、安装和使用。
下载即视为同意本软件使用许可协议的全部内容。

[The original text of this Agreement is written in Japanese, and this translation does not have any effect, whether de jure or de facto.]


Software License Agreement


Panasonic Industry Co., Ltd., acting through its Industrial Device Business Division (hereinafter referred to as “us”, “our(s)” or "we") grants the Software license on condition that you have accepted this license agreement. Please be sure to read the Software license agreement (hereinafter referred to as this "Agreement") before using the Software, and do not use the Software without first accepting this Agreement.
On starting to use the Software, you will be deemed to have accepted all the terms of this Agreement. Please do not use the Software unless you accept this Agreement.
The Software may incorporate several open-source software programs in addition to proprietary computer programs in our possession or licensed to us. If open-source software programs are incorporated, please see the license statements included in the Software installation package for those programs. If there is any conflict between the license statements in the open-source software program licenses and those in this Agreement, the wording of the open-source software program licenses will prevail.


Article 1. License

We grant you a non-exclusive license to use the Software for the purpose of using our products identified in the Software manual (hereinafter referred to as the "Products") in accordance with the terms of this Agreement. You may not use the Software for the purpose of using third-party products that are not ours.


Article 2. Prohibitions

The following acts are prohibited with regard to the Software.
(1) Altering, reverse-engineering, decompiling, or disassembling the Software, or any other act of a similar nature.
(2) Use of the Software other than by the methods prescribed in the manual provided by us or our website, or any other methods designated by us.
(3) Use of the Software for any purposes other than those prescribed in the manual provided by us or our website, or any other purposes designated by us.
(4) Distribution, renting out, leasing, loaning, or the assigning of the Software to any third party.
However, subject to the assignee's agreement to be bound by all the conditions of this Agreement, you may assign the Software license under this Agreement together with the Products.
In this case, you will deliver all the copies of the Software and its annexed documentation to the assignee, and you may not retain any copies of the Software, including backup copies.


Article 3. Disclaimer

We do not warrant the Software's merchantability, fitness for any particular purpose, or non-infringement of third-party intellectual property rights, and do not make any other warranties with regard to the Software.
2. We accept no responsibility for damage of any kind (including direct, indirect, incidental, consequential, and special damage) that results from the use of the Software, loss of its use, or any bugs, security holes, malfunctions or other glitches, or otherwise resulting from use of the Software.


Article 4. Effective term

This Agreement comes into effect when you accept it and start to use the Software.
2. If you are in breach of any of the provisions of this Agreement, we may immediately terminate this Agreement.
3. Within four weeks after this Agreement is terminated, you will return to us, or erase or destroy all of the Software and its copies at your expense.


Article 5. Compliance with export laws

You must comply with the export control laws, regulations, etc., of all countries that have jurisdiction over the parties hereto (including the Foreign Exchange and Foreign Trade Act of Japan, and export control regulations based on United Nations Security Council resolutions). If qualifications or appropriate approval by governmental agencies are required, it is prohibited to export the Software directly or indirectly to any countries without such approval. It is also prohibited to use or sell the Software directly or indirectly for military purposes.


Article 6. Ownership of copyright, etc.

Except for open-source software programs, all copyrights and other intellectual property rights to the Software are vested in us or our licensors.


Article 7. Upgrading

It is within our discretion whether or not to offer Software upgrades or updates at any point in the future. If an upgrade or update is offered, a fee may be charged.
2. If a Software upgrade or update is offered, whether on a chargeable or non-chargeable basis, this Agreement will apply as part of the Software unless otherwise specified by us when the offer is made.


Article 8. Limitation of liability

In no event will our liability associated with this Agreement or the Software exceed 10,000 yen.


Article 9. Modifications

We may modify this Agreement at any time at our discretion if
(1) the modifications to this Agreement are in conformity with your interest in general; or
(2) the modifications to this Agreement are not incompatible with the purpose of this Agreement, and are rational in light of the need for and reasonableness of the modifications, and other circumstances related to the modifications.
2. If we modify this Agreement pursuant to the preceding paragraph, we will announce our plan to modify this Agreement, the content of the modified version of this Agreement, and the date on which the modifications will come into effect on our website no later than two weeks before the effective date of the modified version of this Agreement. However, we may effect modifications without notice to you if they are of a minor nature or are not detrimental to you. This Agreement will be modified on the date that the modifications come into effect.


Article 10. Governing law and jurisdiction

This Agreement is governed by the laws of Japan.
2. If any dispute arises in connection with this Agreement, the Osaka District Court will have exclusive jurisdiction over such dispute.


[1st Apr. 2024] Version


安装方法

1.点击下载链接,指定保存路径。

指定保存的位置,点击[保存]按钮。
开始下载文件。

如果您不同意 "软件许可协议",将无法下载本软件。
请完整阅读 "软件许可协议" ,并勾选 "我已确认许可协议"。

标题 语言 版本 文件大小 更新日期
CN-Simplified 2.60 1.5MB 2024年4月1日

2.Decompress the downloaded file.

 

3.Double-click the file in the decompressed folder to activate FPLoader.

 
 

返回页首