KS1 Signal Converters Firmware Ver.1.07

请在使用版本升级之前仔细阅读以下信息。

限制事项

The latest firmware for the KS1 Signal Converters is available. Configurator WD Ver1.42 or higher should be installed to use the latest firmware. If you use the version below 1.42, upgrade it to Ver. 1.42 or higher from the software download page.

The firmware of the below products is updated;

  • AKS1202 Firmware

Version-Up Information for AKS1202(Ver.1.07)(September 1, 2014 update)

Fixed the followings

  • - Communication fault correction at the time of more connection.

Version-Up Information for AKS1202(Ver.1.05)

Fixed the followings

  • Behavior that the unit might be frozen by rewriting memory when KS1 receives response data in certain condition on COM2 (RS485) serial communication.

Version-Up Information for AKS1202(Ver.1.04)

Fixed the followings

  • Behavior that received data from slave unit is deleted, when KS1 redoes the transaction during corresponding in certain condition with termination less setting on RS485 serial communication.

Version-Up Information for AKS1202(Ver.1.03)

Fixed the followings

  • MODBUS TCP (RTU, ASCII) Protocol available (addition).
  • Convect the behavior that KS1 returns a previous response before KS1 receives a response from slave when the master unit disconnects and connects TCP connection again after it initially sends a command to KS1.
  • Default value of time out in Ethernet is changed from 0s to 60s.

Version-Up Information for AKS1202(Ver.1.02)

Fixed the followings

  • AKS1202 judges receive time out, when it receives abnormal response from the connected device with Mewtocol communication.
  • When connected with multi devices, the setting value of receive time out not becoming as it was set.
  • The maximum setting value of receive time out is expanded to 300sec.

Version-Up Information for AKS1202(Ver.1.01)

Fixed the followings

  • The comand where AKS1202 accumulated is sent to the serial communications side when serial communication side doesn't response.

软件使用许可协议

使用本软件的条件是您同意本软件使用许可协议的内容。请仔细查阅内容,必须在您同意的情况下才能下载、安装和使用。
下载即视为同意本软件使用许可协议的全部内容。

[The original text of this Agreement is written in Japanese, and this translation does not have any effect, whether de jure or de facto.]


Software License Agreement


Panasonic Industry Co., Ltd., acting through its Industrial Device Business Division (hereinafter referred to as “us”, “our(s)” or "we") grants the Software license on condition that you have accepted this license agreement. Please be sure to read the Software license agreement (hereinafter referred to as this "Agreement") before using the Software, and do not use the Software without first accepting this Agreement.
On starting to use the Software, you will be deemed to have accepted all the terms of this Agreement. Please do not use the Software unless you accept this Agreement.
The Software may incorporate several open-source software programs in addition to proprietary computer programs in our possession or licensed to us. If open-source software programs are incorporated, please see the license statements included in the Software installation package for those programs. If there is any conflict between the license statements in the open-source software program licenses and those in this Agreement, the wording of the open-source software program licenses will prevail.


Article 1. License

We grant you a non-exclusive license to use the Software for the purpose of using our products identified in the Software manual (hereinafter referred to as the "Products") in accordance with the terms of this Agreement. You may not use the Software for the purpose of using third-party products that are not ours.


Article 2. Prohibitions

The following acts are prohibited with regard to the Software.
(1) Altering, reverse-engineering, decompiling, or disassembling the Software, or any other act of a similar nature.
(2) Use of the Software other than by the methods prescribed in the manual provided by us or our website, or any other methods designated by us.
(3) Use of the Software for any purposes other than those prescribed in the manual provided by us or our website, or any other purposes designated by us.
(4) Distribution, renting out, leasing, loaning, or the assigning of the Software to any third party.
However, subject to the assignee's agreement to be bound by all the conditions of this Agreement, you may assign the Software license under this Agreement together with the Products.
In this case, you will deliver all the copies of the Software and its annexed documentation to the assignee, and you may not retain any copies of the Software, including backup copies.


Article 3. Disclaimer

We do not warrant the Software's merchantability, fitness for any particular purpose, or non-infringement of third-party intellectual property rights, and do not make any other warranties with regard to the Software.
2. We accept no responsibility for damage of any kind (including direct, indirect, incidental, consequential, and special damage) that results from the use of the Software, loss of its use, or any bugs, security holes, malfunctions or other glitches, or otherwise resulting from use of the Software.


Article 4. Effective term

This Agreement comes into effect when you accept it and start to use the Software.
2. If you are in breach of any of the provisions of this Agreement, we may immediately terminate this Agreement.
3. Within four weeks after this Agreement is terminated, you will return to us, or erase or destroy all of the Software and its copies at your expense.


Article 5. Compliance with export laws

You must comply with the export control laws, regulations, etc., of all countries that have jurisdiction over the parties hereto (including the Foreign Exchange and Foreign Trade Act of Japan, and export control regulations based on United Nations Security Council resolutions). If qualifications or appropriate approval by governmental agencies are required, it is prohibited to export the Software directly or indirectly to any countries without such approval. It is also prohibited to use or sell the Software directly or indirectly for military purposes.


Article 6. Ownership of copyright, etc.

Except for open-source software programs, all copyrights and other intellectual property rights to the Software are vested in us or our licensors.


Article 7. Upgrading

It is within our discretion whether or not to offer Software upgrades or updates at any point in the future. If an upgrade or update is offered, a fee may be charged.
2. If a Software upgrade or update is offered, whether on a chargeable or non-chargeable basis, this Agreement will apply as part of the Software unless otherwise specified by us when the offer is made.


Article 8. Limitation of liability

In no event will our liability associated with this Agreement or the Software exceed 10,000 yen.


Article 9. Modifications

We may modify this Agreement at any time at our discretion if
(1) the modifications to this Agreement are in conformity with your interest in general; or
(2) the modifications to this Agreement are not incompatible with the purpose of this Agreement, and are rational in light of the need for and reasonableness of the modifications, and other circumstances related to the modifications.
2. If we modify this Agreement pursuant to the preceding paragraph, we will announce our plan to modify this Agreement, the content of the modified version of this Agreement, and the date on which the modifications will come into effect on our website no later than two weeks before the effective date of the modified version of this Agreement. However, we may effect modifications without notice to you if they are of a minor nature or are not detrimental to you. This Agreement will be modified on the date that the modifications come into effect.


Article 10. Governing law and jurisdiction

This Agreement is governed by the laws of Japan.
2. If any dispute arises in connection with this Agreement, the Osaka District Court will have exclusive jurisdiction over such dispute.


[1st Apr. 2024] Version


安装方法

1.点击下载链接,指定保存路径。

指定保存的位置,点击[保存]按钮。
开始下载文件。

如果您不同意 "软件许可协议",将无法下载本软件。
请完整阅读 "软件许可协议" ,并勾选 "我已确认许可协议"。

标题 语言 版本 文件大小 更新日期
CN-Simplified 1.07 232.1KB 2014年9月1日

2.When the download is finished, double-click the file to extract and begin the installation process.

After extraction, 'ks1sc.bin' file is created for 'ks1sc.zip'.

 

3.Turn on the power of KS1 to connect it to PC directly with LAN cable.

 

4.Change the IP address of KS1 to start IP address setting tool.

Run the Configurator WD from the start menu to select [Setting Software] in [Panasonic MEW Control].Click the search button in order to serach units and select KS1, and click [Edit]-[Setting IP Address] in menu bar.Change the IP Address of AKS1202 displayed in "Setting IP Address" window.

  • *1: Please take notes of IP Address before change as it is required after version-up.
  • *2: Please input first three high ranks of four progression of [Computer] IP address which is displayed in the lower of Configurator WD window  Please input an arbitrary progression that doesn't overlap with [Computer] IP Address to one subordinate position.
The setting change of IP Address is executed by clicking [OK] of "Setting IP Address"window.
 

5.Execute the version-up.

Click the search button in order to serach units and select KS1, and click [Edit]-[Update Firmware] in menu bar. Select the download file of 'ks1sc.bin', and click [OK] for executing the version-up.

  • Please be sure not to power off during transfer. After transfer, search KS1 and check if the firmware version is upgraded to the latest version.
 

6.Change the IP address of AKS1202 to the previous address.

Click the search button in order to serach units and select KS1, and click [Edit]-[Setting IP Address] in menu bar. Reset IP address of AKS1202 which you noted in step 5, and change the IP address by clicking [OK] of "Setting IP Address"window.

 
 

返回页首